50 manufacturing tutorials (tools, materials and steps)
1. Pearl necklace
Materials required :
Tools required:
Steps to make :
Cut a piece of nylon or silk thread approximately 60 cm long.
Tie a knot at one end of the thread.
Thread the beads onto the wire using the beading needle.
Once all the beads have been threaded, attach the other joining ring to the other end of the thread.
Attach the necklace clasp to the connecting rings.
Tighten the knots and cut off any excess thread.
2. Macrame bracelet
Materials required :
Tools required:
Steps to make :
Cut three pieces of cotton thread, each about 1 meter long.
Tie the three threads together at one end and secure them to a flat surface with tape or a clipboard.
Braid the threads using macramé knots (alternating threads from left to right and vice versa).
Add beads as you go, if desired.
Continue braiding until you reach the desired length.
Tie the ends together and attach a bracelet clasp if necessary.
3. Pompon earrings
Materials required :
Tools required:
Steps to make :
Wrap cotton thread around your fingers or a piece of cardboard to create a pom-pom.
Cut the thread at one end to release the pom-pom.
Tie a small piece of thread around the center of the pom-pom to hold it in place.
Trim the ends of the pom-pom with scissors.
Tie a joining ring through the center of the pom-pom.
Attach the earring hook to the connecting ring.
Repeat for the second earring.
4. Resin pendant necklace
Materials required :
Tools required:
Fabrication steps :
Mix the epoxy resin according to the manufacturer's instructions.
Add colorants if desired and mix well.
Pour the resin into the silicone mold.
Insert a pendant or decorations into the resin before it hardens.
Allow the resin to harden completely (usually 24 hours).
Remove the pendant from the mold and attach it to a necklace chain using a joining ring.
Attach a clasp to the chain if necessary.
5. Braided leather strap
Materials required :
Tools required:
Steps to make:
Cut three pieces of leather lace, each about 30 cm long.
Secure the three laces together at one end with a knot or jewelry glue.
Braid the laces together until you reach the desired length.
Secure the ends with a knot or jewelry glue.
Attach a bracelet clasp to the braided ends using pliers.
6. Pearl bib necklace
Materials required :
Tools required:
Fabrication steps :
Cut the base of the breastplate necklace in felt or leather to the desired shape.
Thread the beads onto the beading wire in a pattern.
Sew or glue the beads to the breastplate base.
Repeat until the entire base is covered with beads.
Attach connecting rings to the ends of the breastplate.
Attach necklace clasp to connecting rings.
Adjust chain length if necessary.
7. Polymer clay earrings
Materials required :
Tools required:
Steps :
Condition polymer clay by kneading until soft.
Roll the clay to a uniform thickness with the rolling pin.
Use cookie cutters to cut out shapes in the clay.
Make a small hole at the top of each shape for the joining ring.
Bake clay according to manufacturer's instructions.
Allow pieces to cool completely.
Attach connecting rings and earring hooks to the clay forms.
Repeat for second earring.
8. Elastic pearl bracelet
Materials required :
Tools required:
Steps :
Cut a 30 cm piece of elastic thread.
Thread the beads onto the elastic thread, using a beading needle if necessary.
Continue threading the beads until you reach the desired length for the bracelet.
Tie the ends of the elastic thread together in a tight knot.
Trim excess elastic thread.
Add a drop of glue to the knot for added security (optional).
9. Necklace with natural stone pendant
Materials required :
Tools required:
Fabrication steps:
Thread the nylon wire or chain through the hole in the natural stone.
If using nylon thread, attach a joining ring to each end of the thread.
Attach a necklace clasp to the connecting rings.
Adjust chain length if necessary.
The necklace is ready to wear!
10. Filigree earrings
Materials required :
Tools required:
Steps :
Cut two pieces of wire of equal length.
Use the round-nose pliers to create intricate loops and patterns with the wire.
Add beads to the wire if desired.
Form a loop at the top of each piece of filigree to attach to the earring hooks.
Attach the earring hooks to the loops at the top of the filigree pieces.
Adjust the shape and pattern of the filigree if necessary.
11. Chain and pearl necklace
Materials required :
Tools required:
Fabrication steps :
Cut the chain to the desired length for the necklace.
Thread beads onto nylon or metal wire.
Attach beads at regular intervals along the chain, using joining rings.
Attach a necklace clasp to the ends of the chain.
Adjust chain length if necessary.
12. Pearl cuff bracelet
Materials required :
Tools required:
Steps :
Cut a piece of memory wire to the desired length for the bracelet.
Thread the beads onto the memory wire.
Once all the beads have been threaded, use the round-nose pliers to form a small loop at each end of the memory wire.
If you're using a bracelet clasp, attach it to the loops formed at the ends of the memory wire.
13. Multi-row necklace
Materials required :
Tools required:
Steps :
Cut several pieces of nylon or silk thread of different lengths.
Thread beads onto each thread, using a beading needle if necessary.
Attach each thread to a joining ring at each end.
Fasten the junction rings together and attach the necklace clasp.
Adjust the length of the wires to create a multi-row effect.
14. Pearl and wire earrings
Materials required :
Tools required:
Steps :
Cut two pieces of wire of equal length.
Thread the beads onto the wire.
Use the round-nose pliers to create loops and patterns with the wire around the beads.
Form a loop at the top of each piece of wire to attach it to the earring hooks.
Attach the earring hooks to the loops at the top of the wire pieces.
15. Embroidery thread bracelet
Materials required :
Tools required:
Steps :
Cut several pieces of embroidery thread of equal length (approx. 50 cm each).
Tie the threads together at one end and secure them to a flat surface with tape or a clip board.
Braid the threads together using a single knot or macramé technique.
Continue braiding until you reach the desired length.
Tie the ends together and attach a bracelet clasp if necessary.
16. Necklace with shell pendant
Materials required :
Tools required:
Steps :
Thread the nylon thread or chain through the hole in the shell, or attach a connecting ring to the shell fastener.
Attach a connecting ring to each end of the wire or chain.
Attach the collar clasp to the connecting rings.
Adjust chain length if necessary.
17. Chandelier earrings
Materials required :
Tools required:
Steps :
Cut several pieces of wire of different lengths to form candlestick pendants.
String beads onto each piece of wire.
Use the round-nose pliers to create a small loop at the end of each wire to hold the beads in place.
Attach the wire pieces to a joining ring to create the chandelier shape.
Attach the joining ring to the earring hooks.
Repeat for the second earring.
18. Seed bead bracelet
Materials required :
Tools required:
Steps :
Cut a 30 cm piece of nylon or elastic thread.
String the seed beads onto the thread, using a beading needle if necessary.
Continue threading the beads until you reach the desired length for the bracelet.
Tie the ends of the wire together in a tight knot.
Trim excess wire.
Add a drop of glue to the knot for added security (optional).
19. Twisted pearl necklace
Materials required :
Tools required:
Beading needle
Steps :
Cut several pieces of nylon or silk thread of equal length.
String beads onto each thread, using a beading needle if necessary.
Once the beads are threaded, twist the wires together to create a twisted effect.
Attach a joining ring to each end of the twisted wires.
Attach a necklace clasp to the connecting rings.
Adjust chain length if necessary.
20. Feather earrings
Materials required :
Tools required:
Steps :
Cut a piece of wire or nylon about 5 cm long.
Attach a feather to one end of the wire.
Wrap the wire around the stem of the feather to secure it.
Form a loop at the other end of the wire to attach it to the earring hooks.
Attach the earring hooks to the loops at the top of the feathers.
Repeat for the second earring.
21. Stacked chain bracelet
Materials required :
Tools required:
Steps :
Cut several pieces of chain of different lengths.
Attach a joining ring to one end of each chain.
Attach the chains together to a common joining ring at each end.
Attach a bracelet clasp to the connecting rings.
Adjust the length of the chains to achieve a harmonious layered effect.
22. Lace choker necklace
Materials required :
Tools required:
Fabrication steps:
Cut a piece of lace to the desired length for the choker.
Attach ribbons or chains to each end of the lace with connecting rings.
Attach a necklace clasp to the ends of the ribbons or chains.
Adjust necklace length if necessary.
23. Fabric earrings
Materials required :
Tools required:
Fabrication steps:
Cut shapes from fabric (such as circles, squares or triangles).
Make a small hole at the top of each fabric shape.
Insert a joining ring through the hole.
Attach the joining rings to the earring hooks.
Repeat for the second earring.
24. Bracelet with charms
Materials required :
Tools required:
Fabrication steps:
Cut the chain to the desired length for the bracelet.
Attach the charms to the chain at regular intervals using connecting rings.
Attach a bracelet clasp to the ends of the chain.
Adjust bracelet length if necessary.
25. Wire and pearl necklace
Materials required :
Tools required:
Fabrication steps:
Cut a piece of wire to the desired length.
Thread the beads onto the wire, leaving space at the ends to make loops.
Use round-nose pliers to make loops at the ends of the wire.
Attach joining rings to the loops and secure them to the necklace chain.
Attach a necklace clasp to the ends of the chain.
Adjust chain length if necessary.
26. Crochet earrings
Materials required :
Tools required:
Steps :
Make a slipknot with the cotton thread and insert the hook.
Crochet simple patterns such as circles, flowers or drops of water.
Once the patterns are finished, cut the thread and tuck in the ends.
Attach a joining ring to each crocheted pattern.
Attach the connecting rings to the earring hooks.
Repeat for the second earring.
27. Macramé and pearl bracelet
Materials required :
Tools required:
Steps :
Cut three pieces of cotton thread, each about 1 meter long.
Tie the three threads together at one end and secure them to a flat surface with tape or a clipboard.
Braid the threads using macramé knots (alternating threads from left to right and vice versa).
Insert beads as you braid.
Continue braiding and adding beads until you reach the desired length.
Tie the ends together and attach a bracelet clasp if necessary.
28. Wooden bead necklace
Materials required :
Tools required:
Steps :
Cut a piece of nylon or silk thread to the desired length for the necklace.
Thread the wooden beads onto the wire, using a beading needle if necessary.
Attach joining rings to each end of the wire.
Attach a necklace clasp to the connecting rings.
Adjust necklace length if necessary.
29. Hammered metal earrings
Materials required :
Tools required:
Steps :
Cut the metal plates to the desired shape and size for the earrings.
Use a hammer to hammer the metal and create textures.
Make a small hole in the top of each piece of metal with a punch.
Insert a joining ring through each hole.
Attach the joining rings to the earring hooks.
Repeat for the second earring.
30. Semi-precious stone bracelet
Materials required :
Tools required:
Steps :
Cut a 30 cm piece of elastic thread.
Thread the semi-precious stones onto the elastic thread, using a beading needle if necessary.
Continue threading the stones until you reach the desired length for the bracelet.
Tie the ends of the elastic thread together in a tight knot.
Trim excess elastic thread.
Add a drop of glue to the knot for added security (optional).
31. Fabric and pearl necklace
Materials required :
Tools required:
Fabrication steps:
Cut a piece of fabric to the desired length for the necklace.
Sew the beads onto the fabric in a regular pattern.
Once all the beads have been sewn on, attach connecting rings to the ends of the fabric.
Attach a necklace clasp to the joining rings.
Adjust necklace length if necessary.
32. Wooden earrings
Materials required :
Tools required:
Fabrication steps:
Cut the wooden plates to the desired shape and size for the earrings.
Sand the edges of the wooden plates to smooth them.
Make a small hole at the top of each wooden plate with a drill or punch.
Insert a joining ring through each hole.
Attach the joining rings to the earring hooks.
Repeat for the second earring.
33. Twisted wire bracelet
Materials required :
Tools required:
Steps:
Cut several pieces of wire of equal length.
Twist the wires together to create a twisted effect.
Add beads to the wire if desired by stringing them before twisting.
Form a loop at each end of the twisted wire to attach the bracelet clasp.
Attach the bracelet clasp to the loops at the ends of the twisted wire.
34. Pearl and ribbon necklace
Materials required :
Tools required:
Steps:
Cut a piece of ribbon to the desired length for the necklace.
Thread the beads onto the nylon thread, using a beading needle if necessary.
Tie the nylon thread with the threaded beads to the ribbon, forming knots to secure the beads in place.
Attach joining rings to the ends of the ribbon.
Attach a necklace clasp to the connecting rings.
Adjust necklace length if necessary.
35. Mother-of-pearl earrings
Materials required :
Tools required:
Steps:
Make a small hole at the top of each mother-of-pearl disc, if you haven't already done so.
Insert a joining ring through each hole.
Attach the joining rings to the earring hooks.
Repeat for the second earring.
36. Seed bead necklace and pendant
Materials required :
Tools required:
Fabrication steps:
Cut a piece of nylon or silk thread to the desired length for the necklace.
Thread the seed beads onto the wire, using a beading needle if necessary.
Attach the pendant to the center of the thread.
Attach joining rings to each end of the wire.
Attach a necklace clasp to the connecting rings.
Adjust necklace length if necessary.
37. Sea glass earrings
Materials required :
Tools required:
Fabrication steps:
Wrap the wire around the sea glass pieces to secure them.
Form a small loop at the top of the wire to attach the earring hooks.
Attach the connecting rings to the loops.
Attach the earring hooks to the connecting rings.
Repeat for the second earring.
38. Freshwater pearl bracelet
Materials required :
Tools required:
Steps :
Cut a 30 cm piece of elastic thread.
Thread the freshwater pearls onto the elastic thread, using a pearl needle if necessary.
Continue threading the pearls until you reach the desired length for the bracelet.
Tie the ends of the elastic thread together in a tight knot.
Trim excess elastic thread.
Add a drop of glue to the knot for added security (optional).
39. Seed bead and fishing line necklace
Materials required :
Tools required:
Fabrication steps:
Cut a piece of fishing line to the desired length for the necklace.
String seed beads onto the wire, using a beading needle if necessary.
Attach joining rings to each end of the wire.
Attach a necklace clasp to the connecting rings.
Adjust necklace length if necessary.
40. Cultured pearl earrings
Materials required :
Tools required:
Steps:
Thread cultured pearls onto fine wire.
Use the round-nose pliers to create a small loop at the end of the wire to hold the beads in place.
Attach the joining rings to the loops at the top of the wire.
Attach the earring hooks to the connecting rings.
Repeat for the second earring.
41. Seed bead necklace and chain
Materials required :
Tools required:
Steps:
Cut a piece of nylon or silk thread to the desired length for the necklace.
String the seed beads onto the wire, using a beading needle if necessary.
Attach the beaded wire to the necklace chain.
Attach joining rings to the ends of the wire and chain.
Attach a necklace clasp to the connecting rings.
Adjust necklace length if necessary.
42. Seed bead and copper wire earrings
Materials required :
Tools required:
Fabrication steps :
String seed beads onto fine copper wire.
Use the round-nose pliers to create a small loop at the end of the wire to hold the beads in place.
Attach the joining rings to the loops at the top of the wire.
Attach the earring hooks to the connecting rings.
Repeat for the second earring.
43. Seed bead and chain bracelet
Materials required :
Tools required:
Steps :
Cut a piece of nylon or silk thread to the desired length for the bracelet.
String the seed beads onto the wire, using a beading needle if necessary.
Attach the beaded wire to the bracelet chain.
Attach joining rings to the ends of the wire and chain.
Attach a bracelet clasp to the connecting rings.
Adjust bracelet length if necessary.
44. Seed bead necklace with charm
Materials required :
Tools required:
Steps :
Cut a piece of nylon or silk thread to the desired length for the necklace.
Thread the seed beads onto the wire, using a beading needle if necessary.
Attach the charm to the center of the beaded wire.
Attach connecting rings to the ends of the wire.
Attach a necklace clasp to the connecting rings.
Adjust necklace length if necessary.
45. Seed pearl earrings and charm
Materials required :
Tools required:
Fabrication steps :
String seed beads onto fine copper wire.
Attach the charms to the beads using joining rings.
Use the round-nose pliers to create a small loop at the end of the wire to hold the beads and charms in place.
Attach the joining rings to the loops at the top of the wire.
Attach the earring hooks to the connecting rings.
Repeat for the second earring.
46. Seed bead and wire bracelet
Materials required :
Tools required:
Fabrication steps :
Cut a piece of wire to the desired length for the bracelet.
Thread the seed beads onto the wire.
Use the round-nose pliers to create a small loop at each end of the wire to hold the beads in place.
Attach the bracelet clasp to the loops.
Adjust bracelet length if necessary.
47. Necklace in seed beads and silk thread
Materials required :
Tools required:
Steps :
Cut a piece of silk thread to the desired length for the necklace.
String seed beads onto the thread, using a beading needle if necessary.
Attach joining rings to each end of the thread.
Attach a necklace clasp to the connecting rings.
Adjust necklace length if necessary.
48. Seed bead and silk thread earrings
Materials required :
Tools required:
Steps :
String seed beads onto silk thread.
Use the round-nose pliers to create a small loop at each end of the thread to hold the beads in place.
Attach the joining rings to the loops.
Attach the earring hooks to the connecting rings.
Repeat for the second earring.
49. Seed bead necklace with copper wire charm
Materials required :
Tools required:
Steps :
String seed beads onto fine copper wire.
Attach the charm to the center of the beaded wire.
Use the round-nose pliers to create a small loop at each end of the wire to hold the beads and charm in place.
Attach connecting rings to the loops.
Attach a necklace clasp to the connecting rings.
Adjust necklace length if necessary.
50. Seed bead bracelet with charm
Materials required :
Tools required:
Steps :
Cut a piece of nylon or silk thread to the desired length for the bracelet.
Thread the seed beads onto the wire, using a beading needle if necessary.
Attach the charm to the center of the beaded wire.
Attach joining rings to the ends of the wire.
Attach a bracelet clasp to the connecting rings.
Adjust bracelet length if necessary.
